1 Test Injectable

Any ideas on how to make a pain free 1 Test injectable? I have some powder coming soon, and am very interested in getting this when off cycle.

I know it can be done, Pat Arnold has made one, also research kits now sells a pain free version.

I was also thinking about mixing it with injectable B12, since it helps with painful injections.

One idea from Goanna from Animals board. Not sure if this would do it.

“Pain Free” Sterile 1-Test Injection

Ingredients;
1250mg 1-test ester
8750mg Hydroxy-Propyl Beta Cyclodextrin (HPB)
22ml Sterile Cottonseed oil (or other USP sterile oil)/or bat water.
5ml Benzyl Alcohol (or 50/50 BA/BB)

Equipment, Accessories;
25ml sterile syringe
3 ml sterile syringe
.45 Whatman Sterile Syringe Filter
3 18g 1.5 sterile needles
1 25-30ml Sterile Vial with Stopper and Seal
2 25ml glass vials (screw top)
Milligram scale
Wax paper

Procedure;
1. Place a small piece of wax paper on the scale and weigh out the required amount of 1-test powder. Set Aside.
2. Place another piece of wax paper on scale and weigh out the HPB. Set this aside.
3. Place 5ml of Benzyl Alcohol into a clean vial and add the above powders. Shake vigorously several times and let sit for 45 minutes to 1 hour. You may heat in hot water during the last 10-15 minutes as more of the product will go into solution at higher temperatures.
4. Put an 18g needle on the 3ml syringe and withdraw 2-3ml of oil into the syringe. Re-cap the needle and set aside for later use.
5. Add the remaining oil to the Benzyl Alcohol Solution. Cap the vial and shake vigorously. Let the mixed solution sit for another 45 to 60 minutes, again heating the solution during the last 15 minutes.
6. After the solution is heated, Place an 18g needle on the 25ml syringe and withdraw all the contents of the vial. (At this stage, you may want to pre heat your oven to 250 degrees Fahrenheit)
7. Remove the needle and attach the sterile filter to the syringe. Re-attach the needle to the sterile filter.
8. Begin to sterile filter the solution into the 25ml sterile vial. Be sure to use the third needle to vent the bottle in order to eliminate pressure buildup.
9. When all the solution has been filtered, remove the 25ml syringe and attach the 3 ml syringe to the filter. Now purge the sterile oil through the filter to make sure all the active ingredients are in the vial, not the filter.
10. Remove the syringe/filter combination and place the sterile vial on a small baking pan. Place the vial in the 250 degree oven for 45 minutes. Make sure to leave the 18g needle in the vial so that pressure will escape during heating.
11. When the 45 minutes is up, remove the vial from the oven and let cool. You now have a sterile, oil based solution that contains 50mg of 1-testosterone ester and 350mg of HPB per ml. of solution. Enjoy

I got a question for you, Harvey. Why would you want to run 1-Test? Wouldn't it shut you down just like test? And from what I've seen it is more expensive. Just curious.

I just want to figure out how to do it.

Gains are pretty good for this stuff, from what I have read it doesn't completely shut down natural test level like test would.

I can get 10 grams for a little less than what 10 grams of cyp powder costs.

What type of cycle would you run the 1-test like mg and how often?

What could you do to keep test levels up while on 1-test?

Researchkits is supposed to be painless anybody tried it ?

You would need to inject 100mg ed for 6-12 weeks. Still researching about test levels. Thoughts are calias, or tribulas, from what I have seen it is more of a decrease in libido, than natural test levels.

Harv did you ever end up trying this?

no, I never got the powder, the guy that was going to give me some as a sample decided to sell it as a premade himself.

I read on animals board that a guy made 1test cyp in oil with 3% ba & 10% BB he said it was pretty painless.

There is another site that sells a supersolvent for 1test, I'll try to find the address.

Thanks harv you da man.

Also, is it possible to get 4AD in solution?

Harv, 10% and 3% is the percent of final volume correct?

So if I am making 100ml it would have 10ml BB and 3ml BA, and 87ml of oil, correct?

just about you forgot to include the weight of the powder, it takes up about .75 ml per gram ie 2 grams take up 1.5 ml of the final solution.

I would only do that with 1 or 2 grams to start with incase it doesn't work too well.

I know 4 ad goes into an injectable pretty easy, if I find anything about it, I'll let you know.

Harv, on Animal's board I read you can only get about 250mg/ml max of 1-test in oil, have you heard any different?

Thanks for all your help...:thumbsup:

sounds about right if it is 1 test cyp

regular 1 test would be pretty painful anywhere over 100mg/ml

Harv, I will probably not use 4-AD, I heard it is crap. Do you know if 5 alpha androstenediol (5AA), 3 beta androstenediol, or 4 hydroxy androstenedione will go into solution readily?

Harv,

I am trying to make 175mg/ml of 1-test and I can't get it to go into solution. I added 3% BA and 15% BB. It is cloudy and I have been heating it with the oil added. Any thoughts?

Harvey I always see u up in making stuff. Is is better to make it bro? Is it hard?

OvER JuIcED said:

What type of cycle would you run the 1-test like mg and how often?

What could you do to keep test levels up while on 1-test?

Researchkits is supposed to be painless anybody tried it ?

Click to expand...

I have done researchkits 1-test injectible. It actually feels fine for the first day and the second and third day is a bitch. the pain sneaks up on you. i only did 100mg/ml inj. after doing one cc of it i didnt want to try 2 cc's so i still have some left. Im not real sure what my pain threshold is but i had done a small cycle of sten years ago and that was nothing compared to this. better left as a dermal if you ask me.

100 mg/ml is about the limit for 1-test cyp.
Get your pain free solution @ eagle research.
I will post the link if this is acceptable.

Damn, I heard people getting 175mg/ml into solution.

Well, I guess I'll have to add more oil, BA, and BB.

i apologize for the above statement. actually the 1-test i did was from eagle research and it was 1-test cyp. 100mg/ml I have never tried it from researchkits.com