Is a painless tren a/mast p blend possible at 250mg/ml (125mg each)?

Any of you guys have experience with a tren/mast blend as high as this?

nolimitz said:

Any of you guys have experience with a tren/mast blend as high as this?

Click to expand...

That is 1000% possible to make painless! Its really not that high of a blend in my opinion, i think it would be a lot easier though at 200mg/ml at 100mg and 100mg, but still i think 250mg can be easily made painlessly

Absolutely, however I would get an oxygen mask handy. The cough will kick your ass. The acetate ester in a higher concentration will naturally cause site soreness but can be drastically decreased with low BA content and no BB.

Powderguy said:

Absolutely, however I would get an oxygen mask handy. The cough will kick your ass. The acetate ester in a higher concentration will naturally cause site soreness but can be drastically decreased with low BA content and no BB.

Click to expand...

Would it be safe to assume .9% BA would be a good level? With no BB what is the carrier you would recommend. Would that hold in just oil or would it need to be EO? Or is there another solvent other than BB you would recommend?

I'm planning on trying 1.5% BA, 18%, and 25% eo. I think I might have to bump up the eo to 50%. Does this seem doable powderguy? Thanks in advance.

had the worst tren cough the other day, hit a vein im sure and i felt it coming but finished my pin anyway. tren ace 150mg/ml thought i was having a heart attack lol then coughing too.

goodness said:

had the worst tren cough the other day, hit a vein im sure and i felt it coming but finished my pin anyway. tren ace 150mg/ml thought i was having a heart attack lol then coughing too.

Click to expand...

You don't have to hit a vein to experience this with tren. Its the acetate ester and trenbolone will cause a disturbance in the lymphatic system hence your tren cough. I have experienced this with just 75mg. Tren is always best to pin fast.

nolimitz said:

I'm planning on trying 1.5% BA, 18%, and 25% eo. I think I might have to bump up the eo to 50%. Does this seem doable powderguy? Thanks in advance.

Click to expand...

If your planning to do this with tren in my opinion/experience you should adjust your percentages.
Tren doesn't require more than .9ml BA , BB isn't necessary but you can add it if you feel its necessary. 3.4mls should be max (8%). EO can be used at %50 if you can tolerate it-for those who cant Cottonseed or GSO will do fine- This is if you keep the concentration below 150mg/ml. I have made tren like this. SEE BELOW. This is for high Ml brews if your doing small brews less than 30ml do not exceed .9 MLS BA and 4ML BB. Fully dissolve powder before adding oil.

Common 100mg/mL Recipe for 100mL

10 gram Trenbolone Acetate powder (7.5mL)
1.9mL BA
20mL BB
70.5mL Oil

Will also hold in:

10 gram Trenbolone Acetate powder (7.5mL)
1.9mL BA
15mL BB
75.5mL Oil

Common 100mg/mL Recipe for 100mL NO BB

10 gram Trenbolone Acetate powder
4.3mL BA
87.8mL Oil


200mg/mL Recipe for 100mL EO, No Oil.

20 gram Trenbolone Acetate powder (15mL)
2mL BA
25mL BB
58mL EO
WARNING IF YOU REACT TO EO THEN DO NOT USE. THIS IS FOR THOSE WHO HAVE NO ISSUES WITH EO OR HIGH BB CONCENTRATIONS.

- - - Updated - - -

Cowboy3 said:

Would it be safe to assume .9% BA would be a good level? With no BB what is the carrier you would recommend. Would that hold in just oil or would it need to be EO? Or is there another solvent other than BB you would recommend?

Click to expand...

This will hold in .9BA. You can dismiss another solvent if you heat the oil and add the solvent first, dissolve as much as you can then add the warm oil and continue to stir and dissolve the powder. I posted recipes for both oil and EO for ya.

Did this ever prove working and if so what recepie was followed??

Thanks in advance