Whats goin on guys. I was transfering some gear from satgchets to vials the other day for my upcoming cycle. Well everything was goin fine until my last satchet. When pinning the satchet, the pin went through the other side. I slid the pin back so that it was back in the satchet completely and continued to withdrawl just like normal. I injected in the vial. My question is, will the extra hole cause for much concern with sterility. Is that hole any more exposing then the initial hole made by the pin. Should i not use the gear, or is it good to go. I was thinking of ordering a filter and just extracting it all from the vial and filtering it back in. What do you think. My biggest worry is that after i poke the satchet i let it sit on a paper towel as i extract, but if there was a whole on the other side, could particles get in the satchet? What do you guys think My Npp was one stealth comnpany, my sust was another, the sust is where the problem arose. What do you guys think i should do. Thanks in advance. i dont want to have to dump all the sust, im really thinking about just saying fuck it and using it.
Sterility and Satchets question
- Thread starter Santo224
- Start date
Spiderman
New member
I don't know bud...I've never used satchets before, but I can see how something could get inside if you poked a hole in both sides. However, I just don't have any clue how likely it is. I don't know enough to give you advice on this, but someone else on here will be able to. Seems like you might be able to heat it up to kill anything that got in there, but you will need to confirm this with someone else and hopefully they'll have some more advice on how to do this if it's even necessary. Try posting this in the lab conversions forum and see if you get any help in there. Sry I couldn't be of more help bud.
i would say you are most likley okay. Simply exposing gear to the air wont automatically "unsterilze" it. Think about amps, you break the top off and the gear is momentarily exposed.
As long as the pin didnt touch anything unsterile (i.e. you, the counter top, etc.) it should be okay.
All that being said, filtering is an option but you will still lose some gear during filtering.
As long as the pin didnt touch anything unsterile (i.e. you, the counter top, etc.) it should be okay.
All that being said, filtering is an option but you will still lose some gear during filtering.
S
saudades
Guest
All really great answers, bump them all.
one question, was the hole in the other side of the satchet sitting on the paper towel while you withdrew or were you holdiing it in the air? if the second hole was touching anything other than your pin I would be concerned but if it wasn't you'll be fine. best thing to do is to find out how to sterilze it and then you won't have anything to worry about. good luck and keep us posted.
For a while i was holding the satchet in the air, but yes, about halfway through, i laid it on the paper towel, thats where most of my concern came from. Im gonna look up how to sterilize. If its too much of a process im just gonna say some prayers and go for. Thanks again fellas.
One more questions:
After the gear was in the syringe, i heated the syringe under running hot water, just along the syringe, the needle was capped, and i tried to keep it as far from the running water as possible, is it likely that some water could get in the syringe like this?
One more questions:
After the gear was in the syringe, i heated the syringe under running hot water, just along the syringe, the needle was capped, and i tried to keep it as far from the running water as possible, is it likely that some water could get in the syringe like this?
Last edited:
I wasnt injecting myself, i was injecting the sterile vial. for some reason, i noticed this brand was alot thicker then the brand i tried prior, so i heated it a bit so it would come out a litle easier. Thanks for the reply.
How would this be. If the sterility of the sust is no good to use, would it be horrible to use Test E in place of it. I have Test E on hand, enough to run the same dose. I know it isnt ideal to use a fast acting compound with a slowacting test, but would it be that bad. I would rather use the sust, but if its dirty, would the test e be ok.
How would this be. If the sterility of the sust is no good to use, would it be horrible to use Test E in place of it. I have Test E on hand, enough to run the same dose. I know it isnt ideal to use a fast acting compound with a slowacting test, but would it be that bad. I would rather use the sust, but if its dirty, would the test e be ok.
Similar threads
