Tren ace 75mg/ml
- Thread starter So-Solid
- Start date
For 75 mg/ml I prefer 2.5% BA, and 7.5% BB. You'll hear varying thoughts, and there is a pretty decent window as far as comfort of the end product, but from a medical stand point you are much better off with less BA & BB. They both take a toll on the tissue for the long haul. These ratio's shoot very smoothly at this dosage. I have had many compliments. If you need the exact recipe for a given amount let us know and we'll help you out. Take care. TY
Hey Bro, I'll make this for a 50 ML vial at 75 mg/ml. That will leave you a little left over as well. You could make this at 100 mg/ml and get use the whole 5 G's, but it is rare to get exactly 5 G's out of a package. Most times it is close, but on the low side. If you do opt for the 100 mg/ml version just back your oil down to 41.25 mls, and use 5 G's of powder. The BA and BB will stay the same. Hope that helps.
Oh, and try not to filter as soon as it comes off the heat. If your are using plastic syringes, and filters it will break them down and pass some of the toxins. Won't kill you, but it's one less thing you don't need to put in your body, LOL. It filters a bit harder, but the quality of the end result is much better. You also stand a much better chance of avoiding a product that clouds up after a short peroid. Take care. TY
Oil 42.19 mls
Power 3.75 G's
BA 1.25 ml
BB 3.75 ml
Oh, and try not to filter as soon as it comes off the heat. If your are using plastic syringes, and filters it will break them down and pass some of the toxins. Won't kill you, but it's one less thing you don't need to put in your body, LOL. It filters a bit harder, but the quality of the end result is much better. You also stand a much better chance of avoiding a product that clouds up after a short peroid. Take care. TY
Oil 42.19 mls
Power 3.75 G's
BA 1.25 ml
BB 3.75 ml
Hmmm, to each his own, but I don't think you'll be to happy with 5% BA. The stickies are to get newbies in the ball park. It is obvious you think I'm talking out of my ass, or something. Before you waste your powder on a very rough recipe get a second opinion from Brew, or some of the other experienced vets here. TY
brew
New member
Solid listen to the man, he is full of good info. There is no need to go over 3% ba. 2-3 range is all that is need for sterility issues. The added bb will help it stay in solution and help hold it at the injection site. Only thing more ba will do will result in pain. 5% may not be that bad, but you'll never notice 2.5. I use the same recipe Ty gave you, 2.5 and 7.5, use the powder calc sticky to find out just how much solvents and oil you need. If you haven't bouhgt the kit yet, dont. Much more cost effective to buy the individual peices. If you need shoot me a pm and I'll help you set one up.
Solid, thanks Bro. I don't like to toot my own horn and show up somewhere with a handful of posts and act like I created the world. I hate egos like that. I do try and help folks out so they don't have to repeat the mistakes I made, though. Honestly, I have years of experience making quality gear, toot-toot, LOL. When I first started out I did not know shit from shine-ola. It took me a lot of trial and error along with some very painful errors, LOL to get where I am at today. I'll be glad to help you with anything I can. If I don't know I will be straight up and tell you I don't know. Do get as many opinions as possible though and try and go with the folks you hold in high esteem. Take care Bro. TY
Similar threads
