Need a nice pain free prop conversion.

50ml at 100mg/ml.......can anyone help me out??

use the powder cal make it 2.5 ba and 7.5 bb........painfree I promise

o.k thanks bro.So its just the same as making tren at the same mg/ml then aint it?

Just done a trial run with 1g(.7ml bb,.2ml ba).Ive just looked at it after an hour and it looks like a suspension.I dont think thats right is it.....is there a way to fix it-whats gone wrong?

hummm, did you add everything at once?

Test Prop for 5 grams

5 grams powder
36.25 ml sesame oil
2.5ml Benzyl AlcoholA 5%
7.5ml Benzyl Benzoate 15%
Syringes
Vial
Sterile Vial
Whatman sterile filter

1. Weigh out 5 grams of powder.
2. Place powder in vial.
3. Add BA & BB to the vial.
4. Heat oil in the oven to help sterilize it, heat to at least 212 degrees F. I usually heat my oil at 275 to be sure, I put the oil in a muffin pan, just fill one of the indentions this is plenty for these experiments. Also heat more oil than you need, as you will not be able to get it all out of the pan.
5. Add oil to the vial, save 2 ml of oil in the syringe for later. Gently shake vial.
6. Heat mixture if necessary. I like heating my powder products, by placing the vial in a frying pan, and placing it on the eye of the stove.
7. Place a 18 or 20 gauge needle in the sterile vial attach whatman sterile filter.
8. Place another needle in the sterile vial to relieve the pressure.
9. Draw out solution with a syringe, run though whatman filter.
10. Take other syringe with 2ml oil, run through whatman into solution.

Makes 50 ml @ 100mg/ml

brew said:

hummm, did you add everything at once?

Click to expand...

added powder to solvents and heated till it went into solution,added warm oil then filtered into sterile vial.Everything looked fine until an hour later.Really dont know what ive done wrong.Strange.

Can this be injected??or should i just get rid of it and try again??

Checked it this morning and the powder had totally seperated from the oil.Looked like a lump of glue at the bottom,but goes into suspension when i shake it.

ok, you can work with it. Sounds like you got purity issues with you powder. Go into the calc and use 3.5 and 11. Subtract the amount of solvent you used from the new amounts the calc gives you. Add the solvent. Het a pan of water on the stove on low, you don't want to boil just warm to where the little bubbles for on the bottom. let it sit in there, awirling it every few minutes. this should do the trick after about 10 min or so. Let me know how it goes.

brew,youre a genius.:thumbsup:

4 hours later,and its still clear as crystal.Is this likely to sting like a bitch now because of the extra solvents?

Thanks for your help bro.

probably not........also, your not in the clear yet it could still crash in the near future, but if it does get in touch and I got other tricks without bumping up the solvent anymore

Yeah, he's a smart feller, LOL. Honestly listen to Brew! TY

What the hells going on with this prop?

Everythings been o.k so far,but ive just took it out to do my next shot and its got little crystals in it.First sludge,now crystals......whats next!!

How do i fix it this time??
:angry:

Ok, first let me ask you a question. How does it feel, any pain warmness around the site?

hey brew now help a guy with a painfree deca 300mg/ml lol

brew said:

Ok, first let me ask you a question. How does it feel, any pain warmness around the site?

Click to expand...

It isnt really "painful"tbh,but it does ache for longer than anything else ive ever used.It takes about 4 days for the feeling to go.It reminds me a bit of when i ran sustanon-but worse.

I was in a rush to get it sorted it last night,so i added .4ml of B/B and reheated like you suggested last time.It went back to normal and is still holding(but i know the fookin things prolly gonna mess up again in the next few days)

P.S...the "crystals" i described,looked like little shards of glass.

Ok, the pain you speak of it probably from it crashing in you muscle like it is in the vial. We stop the crashing the pain goes away. Two ways to try this. #1 is to add more solvent, but this may cause discomfort depending on how sensitive you are to ba/bb. I forget, but I think your at 3.5 ba and 11 bb? You could bump it up to 4-4.5 and 15 bb. #2 is a trick of Ty's. He claims that in order to make prop stable at low conc of solvent at 100mg.ml or more you must use heat/cool method. I have never tried it, but I don't doubt him that it works. Get it hot like before then cool it in ice water for say 20min or so. Then heat again, repeat this 3 times. When heating from cold to hot, don't just toss it from ice cold to near boiling, you'll crack the vial. Sit it in room temp water and use the stove on low to slowlly heat it in a 1 or 2 inches of water. This will take some time, but it maybe worth a shot before adding more solvent, as you are approaching the percentages where it will get painful soon.

Theres only about 5 shots left in this vial anyway (coz it was just a trial run with a gram).Whats the worst that can happen from it crashing in the muscle-and does it still work?i can put up with the ache until this vials gone,but im going to use a higher% of solvents for the next batch i think.