kinda new to homebrew,need advice

hey everyone,I'm kinda new to homebrewing, have made test c 200mg deca 250mg both turned out excellent,ran all compounds myself,just made test p @100mg and tren ace @ 100mg where I think I may have made an error was during filtering,thought I had .45 and .22 whatmans,turns out all i had was .45 so I rolled out anyway and bottled both compounds, I didnt make pain free test p and have never really ran that ester before( think once had a vial of ready made tren ace and test p and the pip was incredible bad I couldnt finish the vial. well now im pinning 75mg tren and 50 mg test in same pin the pip is kinda bad,worse depending on where i go.when i just hit the tren theres no pain.whats wierd is the test done solo isnt bad either.could my brews maybe not compatable in same injection? theres not a lot of BA in either,both were done with .2 and .18 which I beleive to be a good foolproof ratio,also my powders come from what I believe to be a legit source,he has always done me right with top notch quality. should I possably refilter both with a .22 is what I have now safe only passing through a .45
any advice is apreciated

outta 80 views,I cant get any input? guess I need to look else where for advice

I would filter through a .22 filter to be completely safe an I usually use 3.5% ba to be sure that it stays sterile.

snm0257 said:

I would filter through a .22 filter to be completely safe an I usually use 3.5% ba to be sure that it stays sterile.

Click to expand...

thnx for jumping in and helping brutha, we could use some more knowledgable guys in this lab forum

so should I pull all out of vials and heat again then add the difference of BA to bring it up from 2% to 3.5 then filter with .22(have some now) it actually seems to be holding fine,but I dont want any infection. 3.5% doesnt seem bad,I've seen some say to use 5% BA & 15% BB that seems like a bit much and probably has one hell of a sting to it...anyhow thanks bro.

amorse67 said:

so should I pull all out of vials and heat again then add the difference of BA to bring it up from 2% to 3.5 then filter with .22(have some now) it actually seems to be holding fine,but I dont want any infection. 3.5% doesnt seem bad,I've seen some say to use 5% BA & 15% BB that seems like a bit much and probably has one hell of a sting to it...anyhow thanks bro.

Click to expand...

bump for amorse67 question

amorse67 said:

so should I pull all out of vials and heat again then add the difference of BA to bring it up from 2% to 3.5 then filter with .22(have some now) it actually seems to be holding fine,but I dont want any infection. 3.5% doesnt seem bad,I've seen some say to use 5% BA & 15% BB that seems like a bit much and probably has one hell of a sting to it...anyhow thanks bro.

Click to expand...

If your solution is holding with the 2%, it should be fine. I have used the 5% BA 15% BB, but it had one hell of a bite to it brother. A close friend of mine uses the 2% BA 18% BB and it holds good for him with no pip. After seeing his, I adjusted mine to 3.5% BA and 16.5% BB and it is much easier on the ass so to speak.
If you're concerned with sterility, you can pre-heat your oven toaround 185-200 degrees. Put a needle in the vial to vent, but only put it in far enough to vent and not touching the oil in the vial. Place the vented vials on a baking pan of some sort that wont turn over and bake for 15 minutes. Remove them for about 5-10 minutes and then repeat 2 more times.
Hope this helps ya brother. You can also use this baking method for Cypionate thats crashed out of solution...
Austin

I just made test prope for my girl I pinned it a few times last week PAINLESS.
100mgs/50ml
powder-5gr.
BB-7.5
BA-2.5ml
GSO/EO-50/50-18ml each
Im not big on blends I'll make seperate and pin in the same pin.
Dont know what Recipe you used but for what its worth....