Knot at injection sites

drtbear1967

drtbear1967

Musclechemistry Board Certified Member
If you have been on cycle for anytime period, then you have gotten a knot at your injection site. I have had this happen in my shoulders and well as the hips. What I have done to help get the compound to break up and be absorbed into the muscle is very simple. I will either get a hot water bottle or a heating pain and put it on the area for a few minutes. This provides the warming needed to thin up the oil and allow it be absorbed. Now I will have to say that since I have moved to a 25 gauge needle, I have not had very many knots.

I think that when you use a bigger gauge needed you have the tendency to inject faster, which can have a direct correlation to the development of a knot. If all you have is bigger needles, just take your time and go slow. Sing the happy birthday song and make sure you finish your shot just as you finish the song.

Just a nugget of information. Hope it helps.
 
drtbear1967 said:
If you have been on cycle for anytime period, then you have gotten a knot at your injection site. I have had this happen in my shoulders and well as the hips. What I have done to help get the compound to break up and be absorbed into the muscle is very simple. I will either get a hot water bottle or a heating pain and put it on the area for a few minutes. This provides the warming needed to thin up the oil and allow it be absorbed. Now I will have to say that since I have moved to a 25 gauge needle, I have not had very many knots.

I think that when you use a bigger gauge needed you have the tendency to inject faster, which can have a direct correlation to the development of a knot. If all you have is bigger needles, just take your time and go slow. Sing the happy birthday song and make sure you finish your shot just as you finish the song.

Just a nugget of information. Hope it helps.
Click to expand...
Very good info right here alot of people get careless after awhile of pinning and start doing it to fast to get it over with.

Sent from my SAMSUNG-SM-G891A using Tapatalk
 
drtbear1967 said:
If you have been on cycle for anytime period, then you have gotten a knot at your injection site. I have had this happen in my shoulders and well as the hips. What I have done to help get the compound to break up and be absorbed into the muscle is very simple. I will either get a hot water bottle or a heating pain and put it on the area for a few minutes. This provides the warming needed to thin up the oil and allow it be absorbed. Now I will have to say that since I have moved to a 25 gauge needle, I have not had very many knots.

I think that when you use a bigger gauge needed you have the tendency to inject faster, which can have a direct correlation to the development of a knot. If all you have is bigger needles, just take your time and go slow. Sing the happy birthday song and make sure you finish your shot just as you finish the song.

Just a nugget of information. Hope it helps.
Click to expand...
Great info 25 gauge is so much better

Sent from my SM-S975L using Tapatalk
 
I draw my gear then run syringe under hot water in sink. I heat with only plastic part under water not needle part. I heat until a couple drops comes out of needle on its own from expansion from heat. Takes about 45 sec. I inject slowly often stopping if muscle tenses and leave pin inside but move until muscle relaxes again instead of pushing against tense muscle. I have alot of scar tissue like I am sure alot of us do. I move over from last time in same area. I only do glutes, outer thigh, delts, and meaty tissue under delt on top of triceps. With only mon and Thurs injections up to 2-1/2 cc I only do glutes.
 
can i say where to get pins, no syringe, cheap on here. bc you can get 100 30 gauge x 1/2 inch for 13.25 or 27 gauge needles x 1/2 inch for 7.25,as well as syringes and other stuff. if not i can pm it to you.
 
pgb said:
can i say where to get pins, no syringe, cheap on here. bc you can get 100 30 gauge x 1/2 inch for 13.25 or 27 gauge needles x 1/2 inch for 7.25,as well as syringes and other stuff. if not i can pm it to you.
Click to expand...


Go for it bro ! And the pm you sent was a class act! Thank you
 
fantastic! thank you presser.
here you go guys and gals, get pins from
GPZ med labs. i think they ship usa only.
order and get 'em in a few days.
 
Last edited:
The feed store has sterile syringes in sealed packages. I even buy the needles in sealed little vail and have reused only syringe part sterilized with new needle. Tractor supply also has them for your pets of coarse. I have used these for convenience. I also have bought LA 200 or oxymycin at feed store went to pharm and told them I need syringes for my animals showing them the medicine that says deep muscle injection. I have done this at local owned Pharms not big chains. I never had a problem with this route. I also have used vet grade gear that was great.
 
You must log in or register to reply here.

Similar threads

PEP PATRIOT52
**Does Cooking Protein Powder Destroy or Denature it?
Replies
0
Views
164
PEP PATRIOT52
PEP PATRIOT52
Presser
Testosterone Injections
Replies
0
Views
214
Presser
Presser
Muscle Insider
Peptide Injection Sites – Subcutaneous vs Intramuscular
Replies
0
Views
275
Muscle Insider
Muscle Insider
Muscle Insider
How to Inject Testosterone – TRT and Bodybuilding
Replies
0
Views
89
Muscle Insider
Muscle Insider
Muscle Insider
Best Site to Buy Testosterone – Safe & Legal
Replies
0
Views
65
Muscle Insider
Muscle Insider
Back
Top