Pinning Help

I ordered a test e/tren e blend - 1ml = 400mg 250-test e/150-tren e

This is my first cycle in 3+ years. 6'1" 215lbs. idk my bf. The first time I pinned my right glute the injection went fine, a day later the soreness was intense enough to stay out of work for 2 days. The injection site got worse and by day 4 I went to the doctor who gave me an antibiotic shot and I take oral antibiotics, he also advised me to keep going with my cycle. I pinned the other glute 2 days ago, same thing...super super soreness, I feel feverish, and overall it feels like I got kicked in the ass by a donkey...

It's now day 7 from my first pin, day 3 on antibiotics and my right glute is fine...left glute not so good... Im on day 2 since injection on my left glute, hard to walk, feel feverish... The soreness in the 2 pins are different, the first pin was crippling soreness... the 2nd pin is manageable but feverish... I have run this same cycle before with nothing near this soreness, but the injections came from 2 vials not pre-mixed.

My question is, is the reason for the noticable soreness because its more concentrated? or is it bad gear? it came from a legit source...

A lot of BA AND BB to hold that concentration and prolly EO IN IT ! that's too big a dose per ml bro , I don't care who sells it , it's just too much in my opinion

Presser said:

A lot of BA AND BB to hold that concentration and prolly EO IN IT ! that's too big a dose per ml bro , I don't care who sells it , it's just too much in my opinion

Click to expand...

that pretty much sums it up, I'm surprised that your doctor told you to keep on cycle

you might want to try adding sterile GSO, with a concentration that high you need to cut it

Your case is a lil different but I found with pinning myself i tend to not hold pin steady and it moves around on me causing soreness now I let the wifey do it.:thumbsup:

dorian123 said:

that pretty much sums it up, I'm surprised that your doctor told you to keep on cycle

you might want to try adding sterile GSO, with a concentration that high you need to cut it

Click to expand...

I thought about cutting the dose in half, instead of 1cc do 1/2 a cc?

tatzoo said:

I thought about cutting the dose in half, instead of 1cc do 1/2 a cc?

Click to expand...

you can try that, but that'll still hurt like a bitch

this is why I don't use anything over 300mg/mL-you can try cooking some of the BA out, I never had much luck with this but others have

the last batch of test E that I got was crashing in my muscle that was painful and caused a lot of swelling so I threw it out-that might be a problem for your batch

Contact the manufacturer. See if anyone else is having issues maybe they screwed a batch up. Thin it out and or heat it up. For heating it up put them in the oven at 220 degrees or simmering water for 20 minutes with sterile needles stuck in the top for venting. If you don't pressure will build up and they might explode. This will sterilize it. It should help alot.

virgin muscle wont help either..hot water bottle and a good masage helps..but yeah cut the gear..sucks getting ill from gear..try a your tricep or delts give your glutes a break u might find when u go back there it wont be so bad...half a cc of gso heated might sort it..if u still get ill dump it.not been ill since stealth gear..man that made me rough cut it with some tren ace and i was fine with it..

raysd21 said:

Contact the manufacturer. See if anyone else is having issues maybe they screwed a batch up. Thin it out and or heat it up. For heating it up put them in the oven at 220 degrees or simmering water for 20 minutes with sterile needles stuck in the top for venting. If you don't pressure will build up and they might explode. This will sterilize it. It should help alot.

Click to expand...

Im going to give boiling it in water a try, is there anything I should be looking for it to do?

not really just watch the clock

- - - Updated - - -

stick the pin in-heat it up and watch the clock

dorian123 said:

not really just watch the clock

- - - Updated - - -

stick the pin in-heat it up and watch the clock

Click to expand...

I brought the water to a boil, turned the heat down to where the water was still boiling. I put 3 sterile needles in the bullseye and let it sit in the boiling water for 20 mins. I watched it the entire time and bubbles would come out of the needles that were poked through the vial.

I just took it out of the water, removed the needles and its sitting on my counter. The level of fluid has gone down about another cc after boiling which is the only noticable change as of right now...

what was the purpose of boiling it? to get the BA level down?

I really appreciate the input

suppose to get the BA level down and rumor has it that it will get the EO level down too

EO is some nasty shit