High mg test/eq combo

brew

New member

• Nov 1, 2004

• #1

Here is the situation. I have 330 Test E AND 200 eq in the same ml. I stick 3mls a wk giving me 1g test and 600 eq. Now I have never gone this high with the two toghter in the same ml. Since they are both soluable in oil, I added 3% ba just for sterility. I use 8 or 9%bb can't remember, just kinda a procationary measrue so it doesn't crash at the site. Now, I took three ml on thurs, and I'll be damned if I don't still notice it today. Gives me a nice lump too. Question is 1) is this normal for such a high mg/ml gear 2) is it crashing at the site 3) could this be remidied by adding 4-5% more bb? 4) am I just a big puss and I should should quit my bitching?

 

shiko24

New member

• Nov 1, 2004

• #2

with such a high mg/ml content (and this is just my .02) I would heat it up once a week just to keep all the contents mixed well what may be happening is some settlement due to the high concentration

 

F

Flexmaster

Guest

• Nov 1, 2004

• #3

i think 2, 3, and 4 are true. especially 4. hehehe:satan:

 

Crimsonsweat

New member

• Nov 1, 2004

• #4

lol..thats funny. its crystalizing and the solvent is irritating the muscles at the site causing inflammation and site soreness.

Heat it with a heat pack, then ice it, do this twice a day or every chance you get heat 20 min ice 10.
Trust me this will work well, even for a puss..lol j/k hey flex started it..

 

brew

New member

• Nov 2, 2004

• #5

Well this puss wants to know if I should up the BB to say 12%? If its crashing in my quad, then some of it is being wasted right? Yeah, the heat pack helped, after I took the three cc I could barely get down the damn steps.

 

F

Flexmaster

Guest

• Nov 2, 2004

• #6

i would imagine. i've been thinking lately how much bb it would take to equal 1ml of ba's solvent capabilities. what do you think, like a 3 or 4 to 1 ratio (bb to ba)? not to hijack your thread though brew...just throwing out an idea and wondering what you thought.

 

brew

New member

• Nov 3, 2004

• #7

That sounds about right, I've been told 3:1 for replacement purposes. I'm gonna heat and add about 4% bb tonight, let you know if I get crippled again.

 

F

Flexmaster

Guest

• Nov 3, 2004

• #8

ok, LMK

 

C

Cordoba

New member

• Nov 3, 2004

• #9

I would draw 1ml of your combo into your pin, then draw 1ml-2ml of sterile oil into your pin, shake it then let it sit a while so it can mix. Problem solved. I also find that warming up the gear before you shoot helps, as does massaging after injection, and taking a hot bath after injection.

 

brew

New member

• Nov 4, 2004

• #10

Yeah, I though of cutting it with more oil, but that defeats my original purpose of keeping vol down. I added 6% bb to toal 3%ba and 15% bb. It was slightly painful while I was injecting, but with a heat pack and 20 min I was ready to go.

 

C

Cordoba

New member

• Nov 8, 2004

• #11

I prefer injecting more ml at a lower mg/ml ratio. I find it less painfull.

 

EatingMachine

New member

• Nov 29, 2004

• #12

Cordoba said:

I prefer injecting more ml at a lower mg/ml ratio. I find it less painfull.

Click to expand...

Bump that, I usually go 300mg/ml on my test enan or cyp and everything else at 250mg/ml. That way I can easily remember what mg/ml I am injecting, since my deca, eq, tren e are all the same strength 250 mg/ml.

By keeping everything relatively low I can use the same solutions for spot injections without crippleing myslelf. Also at those dosages with grapeseed oil, they will push through a slin pin, which is nice for spot injections.