Test P & Test E
- Thread starter pkjr
- Start date
View attachment 16394
This is basically what I was going to follow but then i saw the BA and thought Pip in my mind..
Tbh idk how to understand the calculator to make 125mg or 275mg doses. Don't make sense to me, even though I'm good in math lol
This is basically what I was going to follow but then i saw the BA and thought Pip in my mind..
Tbh idk how to understand the calculator to make 125mg or 275mg doses. Don't make sense to me, even though I'm good in math lol
charliebigspuds
New member
There is tried and true recipe on here I've used them. most rule of thumb is 2ba 15 bb. Only thing to say about pip is all short estre give me pip and I don't go over 100 for that reason. In fact my prop at the mo is 75mg ml.
test E D I can go 333mg no pip
test E D I can go 333mg no pip
Brother I'm the same way with math....... and I'm 2 yr's out from having my masters in structural engineering and minor in Nuclear Power Generations. Give me a minute and I'll find a posst on basic recipe's that was recently posted, I really liked it.
Why do you want it at 125mg?
OK........ Let's try this one. It's a recipe for Test Prop at 75 mg/ml:
1 ml BA
20 ml BB
7.5 g Test Prop
72 ml GSO (or oil of choice) ADD ALL TOGETHER!
_________________________
100.5 ml -------> 7.5 g of raw= 7500 NOW DIVIDE 7500 BY 100.5
7500/100.5=74.62=75 mg/ml TO CONVERT TO 125 MG/ML ADD 5.5 g TO 7.5 g (test prop raw) AND HERE IS THE NEW RECIPE
1.0 ml BA
20 ml BB
13 g Test Prop
72 ml GSO (oil of choice)
___________________________
106 ml/13000=122.641=123 mg/ml
I hope my math is right, please someone correct me if i am wrong. If it's right, then compliments to PG he taught me everything....... If they are wrong it Presser's fault (lol) I coppied from him.
1 ml BA
20 ml BB
7.5 g Test Prop
72 ml GSO (or oil of choice) ADD ALL TOGETHER!
_________________________
100.5 ml -------> 7.5 g of raw= 7500 NOW DIVIDE 7500 BY 100.5
7500/100.5=74.62=75 mg/ml TO CONVERT TO 125 MG/ML ADD 5.5 g TO 7.5 g (test prop raw) AND HERE IS THE NEW RECIPE
1.0 ml BA
20 ml BB
13 g Test Prop
72 ml GSO (oil of choice)
___________________________
106 ml/13000=122.641=123 mg/ml
I hope my math is right, please someone correct me if i am wrong. If it's right, then compliments to PG he taught me everything....... If they are wrong it Presser's fault (lol) I coppied from him.
Powderguy
MuscleChemistry Registered Member
The BB in those conversions is too high. It must come down to around 11% for both esters. Believe it or not BB is not needed in TE.
Ive been working on a recipe for you to get the numbers you want with as little pip as possible. Be patient, or try one of those but remember that high BA aand BB will give you pain and scaring in the muscle tissue.
- - - Updated - - -
Private forum under Brew supply bro..good advice and places to get supplies there
Powderguy
MuscleChemistry Registered Member
When you do your brew heres some helpful advice: Add your powder to your BA & BB, make sure you heat it in a water bath, or use a magnetic stirrer, hot plate whatever but gradually heat it while you swirl it to fully dissolve your powder in your solvent, even if you add a little at a time make sure its fully dissolved and as clear as you can get it.
Test Prop will be clear-as well as Cyp and a few others.
Test E will be milky white but have no viscosity (not thick) It will resemble skim milk.
After you have done this add your heated oil or add oil and slowly heat it while stirring or swirling. This will saturate all the components and bind them together thus preventing a crash. If this does crash then you simply have to resolve it by adding more volume of oil to lower the concentration.
After all oil is added and powder is dissolved and you have added it all together let it sit and cool to room temp before filtering and to see if your solution will crash or stay suspended in solution.
If its good after 1 hr then proceed to filter. you may heat again slightly but not so hot to damage the filter. Heated BB will eat through rubber.
Begin your filtration process.
Make sure you keep all areas sterile as possible and when your letting your solution sit make sure you cover it with saran wrap or foil as not to let dust settle into it. keep us posted and thanks for posting that here so that others may assist and others may learn.
Test Prop will be clear-as well as Cyp and a few others.
Test E will be milky white but have no viscosity (not thick) It will resemble skim milk.
After you have done this add your heated oil or add oil and slowly heat it while stirring or swirling. This will saturate all the components and bind them together thus preventing a crash. If this does crash then you simply have to resolve it by adding more volume of oil to lower the concentration.
After all oil is added and powder is dissolved and you have added it all together let it sit and cool to room temp before filtering and to see if your solution will crash or stay suspended in solution.
If its good after 1 hr then proceed to filter. you may heat again slightly but not so hot to damage the filter. Heated BB will eat through rubber.
Begin your filtration process.
Make sure you keep all areas sterile as possible and when your letting your solution sit make sure you cover it with saran wrap or foil as not to let dust settle into it. keep us posted and thanks for posting that here so that others may assist and others may learn.
I'll be waiting patiently, thanks brother.
