Recommend: 0
Thread: First Test E Brew.
-
07-25-2017, 02:23 PM #1
- Join Date
- Jul 2017
- Posts
- 6
- Rep Power
- 0
-
07-27-2017, 05:04 AM #2
- Join Date
- Dec 2016
- Posts
- 0
- Rep Power
- 0
-
12-07-2018, 01:04 PM #3
- Join Date
- Feb 2018
- Location
- Top Secret
- Posts
- 12
- Rep Power
- 0
My percentages for Test E 300 in MCT oil:
1%BA 5%BB (I used 7%BB last batch to make thinner)
I put MCT oil in beaker, add powder, then add BB.
Order doesn't matter, just put it in beaker.
Bring to 180F while stirring whole time.
I don't have a magnetic stirrer, done by hand.
Heat measured using stem thermometer.
NOTE/IMPORTANT: Research effective stem coverage and types of stem thermometer. You must submerge the correct amount of the thermometer for accurate reading.
Once I reach 180F I remove from heat and continue stirring down to 160F.
Put back on heat source and I bring it back to 180F again. Remove from heat and stir until 140F.
Add BA.
Stir until it reaches 105F and then begin to filter using bottle top filter that I sterilized.
DO NOT POUR ALL OF YOUR GEAR IN THE FILTER AT ONCE!.That way if there is a malfunction you don't lose all your gear.
I will warm up gear back to 105F because it cools while I was filtering other gear.
Filter remaining amount.
I put 20G needle on 60ml syringe.
I pour directly/backfill into 60ml syringe.
Put cap back on media bottle.
I fill sealed sterile vials using 27G as a vent in top of vial. I swipe vials with alcohol girst and allow to evaporate. Fill vials.
Remove plunger from 60ml syringe and backfill again. Fill more vials.
When you pour into 60ml syringe, move quickly because it will begin to drip from 20G needle.
After filled, place plunger in back of syringe, but dont push, just seal the syringe, then flip over to get air at top and push in syringe plunger.
Same recipe and procedure for Deca 300.
- - - Updated - - -
I meant media bottle that I sterilized. The bottle top is already sterile of course.
-
12-07-2018, 01:15 PM #4
-
12-07-2018, 01:22 PM #5
-
12-08-2018, 12:25 AM #6
-
12-08-2018, 05:10 AM #7
Seems like the autofil filters are really good. PES-membranes can filter gear containing BB with no problems if it's only a small amount and it's filtered fast.
PES millipore filters suck though.
PP = polypropylene funnel! I think they are the only company that writes what the actual funnel is made from.
-
12-08-2018, 01:06 PM #8
-
12-11-2018, 11:49 PM #9
- Join Date
- Sep 2016
- Posts
- 3,675
- Rep Power
- 2147487330
Only go into media bottle on vac bottle top.
Solvents eat away wrong materials sometimes not available.
Zap cap bottle top best when I did for self and into media then pull out with 60ml syringe and fill sterile vials.
I would peel crimps remove rubber and fill vials to mark put rubber back and recrimp..
Takes so long needle filling with vent I just assume have used syringe filter
Sent from my SAMSUNG-SM-G890A using Tapatalk
-
12-11-2018, 11:50 PM #10
-
12-12-2018, 12:29 AM #11
-
12-12-2018, 12:31 AM #12
Similar Threads
-
Very first brew NPP and Test PP
By pavetim in forum Steroid Powder Recipe DiscussionReplies: 12Last Post: 07-20-2015, 07:10 PM -
my new home brew test acetate & npp
By yossi1711 in forum Steroid Powder Recipe DiscussionReplies: 11Last Post: 07-28-2013, 02:11 AM -
50ml Test E - Home Brew? WTF?
By tatzoo in forum Anabolic Steroid ReviewsReplies: 13Last Post: 12-30-2009, 10:51 AM -
Does Home Brew Test Prop Hurt?
By TheBomb in forum MuscleChemistry DiscussionReplies: 9Last Post: 04-25-2003, 08:35 PM