Thanks Thanks:  0
Recommend Recommend:  0
Likes Likes:  0
  1. #1
    MuscleChemistry Newbie Board Certified Psy.D

    Join Date
    Nov 2018
    Location
    Most likely at the gym
    Posts
    71
    Rep Power
    183

    Default Trestolone phenylpropionate recipe?

    Anyone have a recipe for trestolone phenylpropionate?
    I have been searching but all I find is trestolone acetate. If I can't find one I am thinking just do something like a NPP recipe? I can't even find trestolone phenylpropionate's melting temp so I am totally blind. Pretty sure 20%bb and 2%ba should do it at 100mgs but I would rather get some input from someone who has gone down the trestolone phenylpropionate brewing road before.

    I see all the UGLs selling 50mg trest acetate but I think that is because of how expensive the raws are. Plus it's newer and supposed to be powerful.

    I have seen NPP as low as 16%bb at 100mgs but I know they are different yet the ester should give them some similarity when brewing, or am I totally off on this?

    Can anyone help me?
     

  2. #2
    MuscleChemistry Newbie Residency Training
    jstarks11's Avatar
    Join Date
    Feb 2011
    Posts
    19
    Rep Power
    0

    Default

    10g Trestolone PP
    53.65ml MCT oil
    17.85ml Safflower Oil
    18ml BB
    2ml BA
    Equal 100ml at 100mg/ml

    Now,Brew this, take up to 120C then let sit for 24hours. IF that crashes (which I don't think it will but CANNOT gaurantee) But if it does, ADD:

    20.35ml MCT
    6.8ml Safflower
    6.1ml BB
    .7ml BA

    This will bring you to, 134ml, at 75mg/ml. That should work fine. Take overall heat up to 120C and for safety sake let sit for 24 hour. Should be fine, heat back up to 55C and filter.
     

  3. #3
    MuscleChemistry Newbie Board Certified Psy.D

    Join Date
    Nov 2018
    Location
    Most likely at the gym
    Posts
    71
    Rep Power
    183

    Default

    Wow! Thank you!

    I only have MCT and GSO, can GSO take place of the safflower?

    When you let it sit for 24 hours do you just leave it in the beaker exposed to the air? I have a left over receiving vessel from my sterile vacuum filter set ups, I could clean that out and let it sit in that for the 24 hours since I will still be filtering after I do that then it should be ok right?

    Any chance you know the displacement and melting point of trestolone phenylpropionate?
     

  4. #4
    MuscleChemistry Newbie Board Certified Psy.D

    Join Date
    Nov 2018
    Location
    Most likely at the gym
    Posts
    71
    Rep Power
    183

    Default

    Well I brewed the trestolone phenylpropionate.
    I went with the "tried and true" default of 2%ba and 20%bb. Now I did a 50/50 blend of gso and mct. I couldn't really find a displacement number for the trest phenylpropionate so I played with the calculator a little bit. Also I had just short of 10g of powder it was like 9.84 or something like that. I always like to make my stuff slightly more concentrated than the specific target and in this case it was 100mg per ml.

    So I put in
    9.84g of trestolone phenylpropionate
    20ml bb
    2ml ba
    32ml gso
    32ml mct

    Like I said I like to make my stuff a little more concentrated than what it is "supposed" to be. I was suppose to have right at 70 ml of carrier oil according to the calculator. So I shorted the carrier oil by 6 ml this along with the raw powder being just under the full 10g resulted in 8 vials filled with just over 11mls each. I figure I ended up with between 90 and 92mls by the end. That is consistent give or take with the little bit that pooled at the bottom of the heating beaker after I poured into the filter. There was also about 1/2ml left on top of the filter that the pump couldn't suck through and after I did my best to get everything out of the receiving vessel I left it tilted and sitting for a few hours and about 1/2-3/4 of a ml pooled at the bottom.

    I let the vials sit for three days, no crashing. I have even pinned it, no PIP. I usually like to let the vials sit longer but I had pushed back the brew time wise just a little too long hoping to find actual displacement numbers, melting points, and possibly a tested recipe.

    I probably could have gotten away with lower bb but since it was a shot in the dark I just went 20%. (Actually slightly over with the "missing" raw weight and the shorted carrier oil). The only reason I blended my carrier oil was because I didn't have enough of one to make the entire batch so a 50/50 blend seemed like a good way to go.
     

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Log in

Log in