Putting IGF in the same syringe as your gear...

B

BiggerStronger

Member

• Jun 2, 2006

• #1

Lately I've been putting my IGF1 in the same syringe with my gear. I first draw up my gear with a 3cc syringe. Then I draw up my IGF1 in a insulin syringe. I take the needle off the 3cc syringe inject it onto the top of my gear put the needle back on the 3cc syringe and shoot all together. What do you guys think of doing it this way? It saves me from doing multiple injections each time. I do about 100mcg E3D. So far the results have been great. Hunger, pumps, and a general difference in body composition.

 

S

saudades

Guest

• Jun 2, 2006

• #2

As long as it is water-based with water-based, you're okay. (Shouldn't be doing it if it is oil-based with the water-based IGF.) I don't see any more of a benefit to mixing them other than less frequent injections. Results would be the same regardless. I've done 100 mcg of IGF before--works great!

 

brew

New member

• Jun 2, 2006

• #3

I don't get why people say not to mix oil and water. Done it beofre there is NO problem and I actually like it. loading the oil first helps keep the water based (winny) from cloggin up the smaller sized pins, kinda a lube to help the susp. go thru.

 

M

mikeswift

New member

• Jun 2, 2006

• #4

I know other people that do it as well, I think the problems occur when people try and shake the pin to get them to mix... duh. If you do it the way you did you'll have two different compounds that get injected next to each other because as we all do oil and water doesn't mix, if you shake it up you end up with a lot of small pockets of oil and water and that's where things can become problematic

 

Presser

Admin

Staff member

Administrator

Moderator

• Jun 2, 2006

• #5

i would tend to think the oil mixed with the igf would mess up the half life or the absorbstion somehow and possibly render it no good if it wasnt absorbed in time, but i could be way off and clueless as usual

 

S

saudades

Guest

• Jun 2, 2006

• #6

That's what I was thinking too, essentially the effect it could have chemically with different esters and so forth.

 

D

dreww

MuscleChemistry Registered Member

• Jun 2, 2006

• #7

Presser said:

i would tend to think the oil mixed with the igf would mess up the half life or the absorbstion somehow and possibly render it no good if it wasnt absorbed in time, but i could be way off and clueless as usual

Click to expand...

never thought of that, but being as IGF isnt exactly the most stable of compounds.

but since its shot via a slin pin, I dont think that extra little poke is gonna hurt much. If anything, I would want a way to not have to use real full size pins that we all use with oil based AAS.

 

brew

New member

• Jun 3, 2006

• #8

the only way I can see it effecting the absorption time is if the carrier of the IGF a true AA mixure with BW. Alot of research companies use BA as the carrier. This WOULD blend with the oil, and theefore not be absorbed as quickly which would also allow the compound to unwind prior to absorbtion (bad). If it sits on top of your oil and doesn't mix freely, you will be fine. Jsut really depends on you source and what carrier they REALLY use.

 

Crazymank

MuscleChemistry Registered Member

• Jun 3, 2006

• #9

I just really dont understand the purpose... its not like a slin pin, loaded with IGF even counts as an injection... its virtually painless.

 

jaywooly

Guru

• Jun 4, 2006

• #10

You are all wrong as usual...but I wont tell you why this time....

jk, I don't have a clue, I like sticking myself with slin pins and if I did what you were doing BS, I'd feel I'd be missing out on something.

 

D

dreww

MuscleChemistry Registered Member

• Jun 5, 2006

• #11

NormalSucks said:

I just really dont understand the purpose... its not like a slin pin, loaded with IGF even counts as an injection... its virtually painless.

Click to expand...

exactly my point. I can do slin pins all day - its the big ones that I dont like.