Hey guys, I've been reading the board for the last week or two and feel I'm ready to start converting the powders I have. Here's my plan
Equipoise
Powder required: =24grams or 20.4mL
Oil req'd: =42mL
BA%/BAmL req'd: 2%=1.6mL
BB%/BBmL req'd: 20%=16mL
Calculations: (20.4+42+1.6+16)mL=80mL; 24,000mg/80mL=300mg per mL
total Yield: 80mL at 300mg/mL
Test Enanthate
Powder req'd: =24g or 18mL
Oil req'd: =44.4mL
BA%/mL req'd: 2%=1.6mL
BB%/mL req'd: 20%=16mL
Calculations: (18+44.4+1.6+16)mL=80mL. 24,000mg/80mL=300mg/mL
Total Yield: 80mL @ 300mg/mL
I have the homebrewing/filtering steps down to a 'T' using the instructions in the stickies.
Any comments or suggestions on the above? I chose 2% BA and 20% BB b/c I want less painful injections and I've been told 2% BA is plenty for sterilization. And the 20% BB, according to guys I've spoken with, will help thin the solution as well as preventing the test enanthate and eq from crashing and prolong the life of the gear. This is my first real homebrewing experiment. I want to make a small batch for the first go around just in case something goes wrong.
I purchased the following for this "experiment"
1. 250mL Bromex beaker (for mixing the oil, solvents, and powder)
2. Six 60cc syringes LL (for drawing up solutions and filtering)
3. Three whatman 25mm .20µm filters (for filtering, one extra just in case)
4. A dozen 18g needles (again, for filtering the final solution)
5. One vial of 100mL USP sterile filtered Grapeseed oil
6. 25mL of Benzyl Alcohol
7. 50mL of Benzyl Benzoate
8. Six 30mL amber vials (for final storage)
I already have a very good scale, 23g needles to vent the vials while filtering, and the EQ/Test E powders.
Is there anything else I'll need? Anyone see any problems with the recipes I have? Comments, suggestions, concerns, questions, etc. are welcome.
Thanks.
Equipoise
Powder required: =24grams or 20.4mL
Oil req'd: =42mL
BA%/BAmL req'd: 2%=1.6mL
BB%/BBmL req'd: 20%=16mL
Calculations: (20.4+42+1.6+16)mL=80mL; 24,000mg/80mL=300mg per mL
total Yield: 80mL at 300mg/mL
Test Enanthate
Powder req'd: =24g or 18mL
Oil req'd: =44.4mL
BA%/mL req'd: 2%=1.6mL
BB%/mL req'd: 20%=16mL
Calculations: (18+44.4+1.6+16)mL=80mL. 24,000mg/80mL=300mg/mL
Total Yield: 80mL @ 300mg/mL
I have the homebrewing/filtering steps down to a 'T' using the instructions in the stickies.
Any comments or suggestions on the above? I chose 2% BA and 20% BB b/c I want less painful injections and I've been told 2% BA is plenty for sterilization. And the 20% BB, according to guys I've spoken with, will help thin the solution as well as preventing the test enanthate and eq from crashing and prolong the life of the gear. This is my first real homebrewing experiment. I want to make a small batch for the first go around just in case something goes wrong.
I purchased the following for this "experiment"
1. 250mL Bromex beaker (for mixing the oil, solvents, and powder)
2. Six 60cc syringes LL (for drawing up solutions and filtering)
3. Three whatman 25mm .20µm filters (for filtering, one extra just in case)
4. A dozen 18g needles (again, for filtering the final solution)
5. One vial of 100mL USP sterile filtered Grapeseed oil
6. 25mL of Benzyl Alcohol
7. 50mL of Benzyl Benzoate
8. Six 30mL amber vials (for final storage)
I already have a very good scale, 23g needles to vent the vials while filtering, and the EQ/Test E powders.
Is there anything else I'll need? Anyone see any problems with the recipes I have? Comments, suggestions, concerns, questions, etc. are welcome.
Thanks.