Lincoln7echo
New member
Hey guys, looking for a recipe on t400. I thought there was one floating around, but can't seem to locate it anymore. Thanks for any help
Test. 400
- Thread starter Lincoln7echo
- Start date
H
hulkwillsmash
Guest
not to difficult,Lincoln7echo said:
if doing enth just use 2%ba and maybe 10%BB to thin it, , EO may be used in carrier to thin and reduce discomfort if thats an issue,
if doing cypionate, use 2% BA, 20% BB and EO is recomended as carrier to prevent crashing
or.....do 200mg /mL EACH of enth and cyp, in addition to the BA and BB, they'll act as co-solvents for EACHOTHER, to further aid stability of the brew, use 2/20 , BA/BB and some EP in the carrier, and it'll turn out great
Lincoln7echo
New member
I was referring to a t400 mix consisting of test. prop., enanth., and cyp. With my normal cyp. I use a 2%BA to 20%BB. Should I keep this ratio when mixing or should I add in EO as a carrier? If so, how do I calculate amounts when EO is used. Thanks.
H
hulkwillsmash
Guest
2/20 should work fine, eo isn't needed in this but can be used to thin it out and make it painlessLincoln7echo said:
Lincoln7echo
New member
ANybody?
H
hulkwillsmash
Guest
what more would you like to know?Lincoln7echo said:
Lincoln7echo
New member
Sorry about that. I swear I checked and didn't see any replies and was just trying to bump my post. Thanks for the answer. Have any tricks on measuring out the appropiate amounts when mixing in different test powders. I guess t400 is made of 150mg of both cyp and enanthate and 100 mg of propionate?
H
hulkwillsmash
Guest
no trick really, for every ten mL's of gear, multiply the desired mg/mL time ten to get the needed grams per 10mLs (eg. to make test prop at 100mg/mL, you need(100mgx10=1g) of test prop powder. make sense? then just to that for all the compounds you want in it and you'll know how much powder to use per volumeLincoln7echo said:
i'm assuming to have a scale fine enough to measure out .1 ,.01, or .001g
brew
New member
just a word of caution, that high mg/ml is gonna knot up. It becomes trickier the higher mg you go to get something that is comfortable. IMO anything over 300 with enanthate or cyp using ba and bb as solvents is going to cause pain. Can't speak about EO, never brewed with it, but I do know it does have mild pain reliving properties in addition to its solvent capabilites.
H
hulkwillsmash
Guest
this is true for a number of ppl,brew said:
and i can say from experience EO helps quite a bit, i've done enth500 with no EO and cyp500 WITH EO and the EO made a noticable difference
Lincoln7echo
New member
If I wanted to add the EO in, how much. Is there a percentage of EO to oil or what? Just trying to figure out the best way to brew this t400 that I keep hearing is so good.
H
hulkwillsmash
Guest
the percentage/ratio of EO to oil is up to you bro, anywhere from straight oil carrier to straight EO carrier, EO is pricier than oil but thats really the only limiting factor, try different ratios and see what works for youLincoln7echo said:
PS. EO can cause the rubber in the syringe to swell a bit making it hard to push/pull the plunger so thats something else to take into consideration when using higher ratios of EO in the carrier
Lincoln7echo
New member
so, say i need 18ml of oil, it would be ok to just split that in half and make it 9 ml of EO and 9ml of oil? Thanks a lot guys. Really appreciate all the fast replies and help.
H
hulkwillsmash
Guest
that would work great and would have noticable thinning effects on the gear, plus reduced painLincoln7echo said:
Similar threads
