What Size Pins???

[tsingtao]

I prefer the 23g x 1 1/2 Not too big and not too small.

Laters

T.

 

[BiggerStronger]

Sometimes I like to stab myself wildly with a 16g just for fun...lol

 

[MMX2]

I prefer the 23g x 1 1/2 Not too big and not too small.

Laters

T.

That is what I normally use as well unless its in the quads and delts- I use 25g for those.

 

[blacktail]

23g 1 inch

 

[supermannpc]

they should make a 24g
the 25's are good but it takes like 20 min to unload it

 

[mikeswift]

they should make a 24g
the 25's are good but it takes like 20 min to unload it

warm it up a bit bro, makes a huge difference but it'll still be slow just not as slow!

 

[saudades]

I have had the same thoughts about a pin between 23 and 25. I actually have more problems loading it though--takes forever with a 25, but no problem unloading it.

 

[franconian]

23g 1 inch and I like to really jam it in!!!!

 

[NAIR]

warm it up a bit bro, makes a huge difference but it'll still be slow just not as slow!

Okay so I guess I'm a "pussy" since I ordered some 25's about 2 seconds ago(along with some B12!)...So how do i warm this shit up? Like in my hands or nuke it in the microwave or what?... lol

 

[Get_Swole]

just get some water in the sink some hot water let it sit in there for about 4 minutes or so and that should warm it up just enough to get in and out just fine. i personally never had a problem with 25g. and also where did you get your b12 isnt b12 water based???? not sure never used it but i thought it was if it is then that shit will go through even a 27 gauge like a squirt gun.

 

[oldtimer]

I may try 25's I have always used 23.I have never had a problem with them

 

[Crazymank]

25s are how I roll

 

[Get_Swole]

i would def. be down for a 24 guage i think that would be perfect.

 

[jaywooly]

I'm a 25 man here. Done 23's, but love me my 25's.

 

[NAIR]

I'm going to have say 20's at this point. I've only used a 25 and 20 (came with the Mexican deca I have) so far. I don't like the fact that I have to have a needle in my ass for what seems like an hour trying to get inject this shit. I'm referring to the 25's of coarse. No matter how long I let that crap sit in hot water it still takes forever to inject. So, I'll go with he 20's even though it's like sticking a pencil in my ass.

 

[38532nd]

22g 1 inch pins right into the shoulder I love it

 

[vertigorocks]

Glute with the 25 gauge 1 1/2 '' and draw with a 20 gauge. With he gear ive been using it takes a while to push through though, a real PAIN IN THE ASS LMAO!

 

[pincushion]

i draw everything out with 18s, 23 1" glutes and quads- 25 5/8" for bi tri and shoulders, slin pins for everything else......

 

[Get_Swole]

i dont draw with 18's ive noticed that it tears just a little bit of the stopper after over and over use. I dont wanna accidently stick a tiny piece of rubber in my body. Or even just clog up the needle while in the process. I use a 25 guage half the time and i pin and get it over with in about 5 minutes total.

 

[pincushion]

18s does tear little pieces, its worse when im using 50cc jugs.i just try to miss them when i draw.