making test suspension.
- Thread starter TONY1979
- Start date
midwtchamp
Banana
go the muscle chem lab conversion forum or pm harvey the local mad chemist
Jonny English
New member
DangerousGround said:
Ive seen this before,... but you forgot to give the auther credit!
I had it pasted and saved in drafts bro, not sure who author was been saved for some time for faq material.
I did not know there was a patent on it sorry if I never gave you credit who are ya?
Harv?
if so thanks I personally never did this myself did all oil conversions some I wrote some I look up to help others on conversions I have not done and this is one of em.
I did not know there was a patent on it sorry if I never gave you credit who are ya?
Harv?
if so thanks I personally never did this myself did all oil conversions some I wrote some I look up to help others on conversions I have not done and this is one of em.
freakyferg
New member
would this same conversion work if i used half of everything.
35ml peg
5ml ba
5ml bb
5 g powder
35ml peg
5ml ba
5ml bb
5 g powder
freakyferg
New member
i just finished and it came out good, almost too good? When finished should the final product be clear? or what does it usually look like?
DangerousGround said:
i asked because ive tried a few times, and crystalized on me... i mix the bb, ba, peg, powder all in one 150ml vial. i vent the top and set in an oil bath at 180C for several minutes until it is clear as water. i take it off the heat, filter, and about 3 hours later it crystalizes on me.
what am i doing wrong????
im going to grind up 20g or so in coffee grinder and see if that works?? , the powder is bp93 micronized already
i have a feeling it will work after i grind it up :>)
freakyferg
New member
Try heating it for 20 minutes at 275 degrees. I did 35 ml of PEG and 5ml bb 5ml ba mixed it then added 5g of powder, and cooked for 20 mins. I let it set and cool and it is still good today.
OK, it dont work, It must be shit powder or something. I tried it in supersolvent and still didnt work!! Im having much easier time getting winny to work and everything else aswell!
I tried about 20 different times and wasted 200grams atleast... I was only trying for 100mg/cc which isn't high by any means and I played with the ba, bb levels to no avail... ah well
the powder melting point test checks out perfectly so I think its good to go but who knows now, I thing suspension is a lost cause for me now... I will be getting some more S from another source soon and will try that powder..
I tried about 20 different times and wasted 200grams atleast... I was only trying for 100mg/cc which isn't high by any means and I played with the ba, bb levels to no avail... ah well
the powder melting point test checks out perfectly so I think its good to go but who knows now, I thing suspension is a lost cause for me now... I will be getting some more S from another source soon and will try that powder..
S
strider
Guest
Sad! I have made test susp, much like auquaviron and it is still seperate also. I had to shake well before using. made me blow up like dynamite! If it is the micronized then it will pass through syringe and not be so bad.
I can believe you wasted it like that, it was just fine, test susp is not one of those things that dissolves all the way in the solution. It takes pressure and heat also the right mix of solvents and co solvents at the time.
remember that test is not water soluable so PEG wont help it soluablize, BB is a co-solvent so it wont either right away, but BA is a solvent so it will turn clear if its just ba and test powder, but you cannot just do that.
If there is a chance that it will be screwed up then dont waste your time with the amount you wasted it would have been cheaper to buy pre-made.
Stanzanol is a different base powder and can be dissolved without much effort, I have even dissolved it in hot water..lol
Its not a lost cause if you used proper precautions and the right formula, then shake before use and give it a try bro, dont waste it or find a guinea pig.
good luck.
I can believe you wasted it like that, it was just fine, test susp is not one of those things that dissolves all the way in the solution. It takes pressure and heat also the right mix of solvents and co solvents at the time.
remember that test is not water soluable so PEG wont help it soluablize, BB is a co-solvent so it wont either right away, but BA is a solvent so it will turn clear if its just ba and test powder, but you cannot just do that.
If there is a chance that it will be screwed up then dont waste your time with the amount you wasted it would have been cheaper to buy pre-made.
Stanzanol is a different base powder and can be dissolved without much effort, I have even dissolved it in hot water..lol
Its not a lost cause if you used proper precautions and the right formula, then shake before use and give it a try bro, dont waste it or find a guinea pig.
good luck.
ok ill try one or two more times lol...
The only thing I havent tried is upping the ba to 10%, ive tried as high as 7% but not 10% yet, BB ive tried as high as 15%. So this time I will try ba at 10%, bb at 10%,(if that dont work then ill up bb to 15%) heat in a vented vial until clear. filter and let cool. Hopefully the higher amounts will help.
The other S that I threw out, I guess I should have saved and added more solvent. It was solid mass though bro, no way I can shake it up when it is solid hehe...
The only thing I havent tried is upping the ba to 10%, ive tried as high as 7% but not 10% yet, BB ive tried as high as 15%. So this time I will try ba at 10%, bb at 10%,(if that dont work then ill up bb to 15%) heat in a vented vial until clear. filter and let cool. Hopefully the higher amounts will help.
The other S that I threw out, I guess I should have saved and added more solvent. It was solid mass though bro, no way I can shake it up when it is solid hehe...
Mr Olympia
New member
Go with an oil conversion, trust me, only 1xDay injections required, instead of 2xDay.
