So I'm going to brew up some test E 250/ for use in hopefully a 29guage pin for ED injection. (Anything larger that 29 creates scar tissue on me, its just genetic... ) anyway, I ordered EO as I understand it flows better. My question is with a 50/50 gso/EO mix will the EO degrade and breakdown the rubber stoppers? Is any one rubber stopper better than the other(butyl , silica gel, ect? ) I don't want to be injecting rubber into me every day. Thanks
Test E for use in slin pins
- Thread starter Ohyea
- Start date
Ohyea, you may not need ethyl oleate. If you do, store your vials upright you should be fine.
It's not only the rubber stoppers that have a hard time with that particular carrier. Some people have negative reactions from it as well. If you find that using it does create some irritation at the injection site, you may not want to waste your gear.
I made Test E 400mg/ml oil only. Yeah it's a bit thick. I used a 28 gauge. You may want to reevaluate your need.
If you're in a rush maybe thinning it out with EO is necessary. Good luck :wave:
It's not only the rubber stoppers that have a hard time with that particular carrier. Some people have negative reactions from it as well. If you find that using it does create some irritation at the injection site, you may not want to waste your gear.
I made Test E 400mg/ml oil only. Yeah it's a bit thick. I used a 28 gauge. You may want to reevaluate your need.
If you're in a rush maybe thinning it out with EO is necessary. Good luck :wave:
Ok so what I learned here is the silica stoppers are better, keep vials upright and might not need the EO period. I will try oil first. Testquest, you have a recipe for that 400mg/ test e that flows thru 28 gauge you would care to share? I'm excited abt that since I could change to EOD pinning with 400mg/. How is the PIP with that brew and how much do you stick in a site?
I mixed my favorite oils with Test E. I used Fractionated Coconut Oil as a base, Papaya Seed Extract, Grapefruit Seed Extract, and Cherry Kernel Oil. 2% benzyl alcohol.
Like I said it's kind of thick but, my batch looks like its holding.
But I only pin 25units every 3 days SubQ. If you're doing a lot it may be inconvenient. It takes about a minute or so to fill the syringe.
Like I said it's kind of thick but, my batch looks like its holding.
But I only pin 25units every 3 days SubQ. If you're doing a lot it may be inconvenient. It takes about a minute or so to fill the syringe.
Use 2pcs syringe instead of slin pin and draw quick with 22guage and inject with a 28guage?
so I read that the MCT has less viscosity than others but you are saying it holds the test well? Sounds perfect for small pin injections. Have you tried any other steroids with it yet? I need a recipe for NPP and tren ace as well.
so I read that the MCT has less viscosity than others but you are saying it holds the test well? Sounds perfect for small pin injections. Have you tried any other steroids with it yet? I need a recipe for NPP and tren ace as well.
Just draw with the 28 gauge. If you learn how draw with the small pin then, you will learn how to inject with it properly.
Besides, I thought you were worried about your rubber stopper ? 22 gauge isn't going to help.
I cannot vouch for anything but this particular protocol.
thanks
Besides, I thought you were worried about your rubber stopper ? 22 gauge isn't going to help.
I cannot vouch for anything but this particular protocol.
thanks
sosasghost
New member
No offense but have you blended raws before??
LeatherHead
New member
So you're taking your test e sub a instead of I m?
Sent from my DROID RAZR using Tapatalk
LeatherHead
New member
Sub q not sub a
Sent from my DROID RAZR using Tapatalk
Sent from my DROID RAZR using Tapatalk
sosasghost
New member
Its no sweat man, good luck on it. Blending is easy but a slin pin for me isnt deep enough in the muscle
Similar threads
